ISLS18335 Everbuild

Everbuild 175 Universal Acrylic White C3


Product Description

  • Contains anti-fungal agent to prevent mould growth in areas of high humidity, and can be overpainted
  • Range

    -15°C to +75°C

    Chemical Resistance

    Dilute Acids - Fair Dilute Alkaline - Fair

    Aliphatic Hydrocarbons - Fair Aromatic Hydrocarbons - Poor

    Movement Accommodation

    Low to medium (+/- 7.5%) EN15651-1:2012


    Up to 10 years when used as recommended

    Shelf Life

    Up to 36 months when stored in unopened cartridges under cool dry conditions
  • Best results will be obtained by keeping an even pressure on the gun trigger and keeping the gun at a constant angle to the surface being sealed

  • Limitations

    Protect from water for a minimum of 24 hours after application
  • Apply nozzle and cut cleanly at an angle of 45' with an opening slightly larger than the gap to be sealed

  • Internal sealing around PVCu window and door frames


    Can be used in contact with most building and decorating materials but should not be used against bituminous materials
  • floor joints)
  • Before using the product, the user should carry out any necessary tests in order to ensure that the product is suitable for the intended application

  • Sealing cracks and gaps in brickwork, stone and concrete
  • Apply using a standard sealant gun

  • Specific Data


    Ready to use thixotropic paste, viscocity ca

  • Not for use externally when rain is imminent (within 6 hours at 20`C, 12 hrs at 10`C.)

  • Limitations

    Should not be used in conditions of continuous immersion, below ground level, in areas of high abrasion (e.g

  • Sealing around baths, and basins
  • Certain poor quality paints (especially certain vinyl matts) have very little movement in the dry film
  • It is possible for the dry paint film to crack if movement is excessive
  • Moreover, all users should contact the seller or the manufacturer of the product for additional technical information concerning its use if they think that the information in their possession needs to be clarified in any way, whether for normal use or a specific application of our product
  • Product Description
    EVERFLEX 175 UNIVERSAL ACRYLIC SEALANT is an acrylic Sealant, suitable for internal and external use that provides a permanently flexible long lasting seal that adheres to virtually all materials

  • PVCu profile, trim and cladding
  • Overpainting is not necessary

  • Note: this product is a flexible
  • Care should be taken at this point not to saturate the surface as this will delay drying
  • The same applies to any information provided verbally by telephone to any prospective or existing customer.
  • Any excess sealant etc., can be removed using a sponge and warm water

  • Shelf Life
    36 months from date of manufacture

    The technical data contained herein is based on our present knowledge and experience and we cannot be held liable for any errors, inaccuracies, omissions or editorial failings that result from technological changes or research between the date of issue of this document and the date the product is acquired
  • The information detailed in the present technical data sheet is given by way of indication and is not exhaustive

  • Do not use around shower trays

  • Application
    Cut the tip of the cartridge taking care not to damage the thread

  • An adhesive for bonding polystyrene coving and tiles

  • Surface Preparation
    All surfaces must be clean and dust free

  • Health & Safety
    Consult MSDS for full list of hazards

    Store in cool dry conditions and protect from frost
  • Note that damp or humid conditions will significantly extend the cure time
  • 250,000cps

    Specific Gravity


    Elongation at Break (%)

    >100% ISO8339

    Hardness (Shore A)

    Approximately 40

    Tack Free Time

    15 to 60 mins, dependent on thickness, ambient temperature and humidity

    Full Cure

    3 to 5 days, dependent on thickness, ambient temperature and humidity

    Solids Content


    Slump Resistance

    No slump ISO7390

    Application Temp
  • Use GENERAL PURPOSE SILICONE for greater movement capabilities
    Do not overpaint until a surface skin has formed
  • Do not expose to water until fully cured
  • Smooth down within 20 minutes of application using a wetted spatula, piece of wood or wetted finger

  • Benefits

    Permanently flexible
    Adheres to most surfaces

  • Areas For Use

    Internal and external sealing around timber and metal window and door frames

  • Mould resistant
  • Range

    +4°C to +40°C

    Service Temp

  • An adhesive for bonding cork tiles and wood block flooring
  • This product an be applied to slightly damp, but not wet surfaces

  • Not for use in conjunction with bitumen or asphalt
  • Our guarantee applies within the context of the statutory regulations and provisions in force, current professional standards and in accordance with the stipulations set out in our general sales conditions

  • Gap and crack filler prior to decorating
  • All loose or flaking surface coatings, and old sealant and mastic joints, should be removed before application

  • Easy clean up
    Certified under the harmonized European standard EN15651 for façade and sanitary applications in compliance with the Construction Product Regulations
  • Can be overpainted after @ 1 hour
  • Highly porous substrates such as new plaster should first be primed with Everbuild PVA bond diluted 1:4 with water
  • If a quicker cure is required, use GENERAL PURPOSE SILICONE (6 hour cure)

  • Do not attempt to abrade when cured
  • Note that low temperatures will significantly retard the cure, skinning time

Manufactured by










Usually Despatches Within 2 Working Days
Add to Wishlist